Intel Active Management Technology (AMT)

From ThinkWiki

Jump to: navigation, search

Intel Active Management Technology (AMT)

Some models offer this specific feature.

AMT Version(s)	Wired Manageability	Wireless Manageability	Processor	Operating System	Models Supported
1.0	Yes	No	ARCtangent-A4	ThreadX	N/A (was featured only in the 82573E Gigabit Ethernet Controller)
2.0, 2.1, 2.2	Yes	No	ARCtangent-A4	ThreadX	N/A (was featured only in the 82Q965 Memory Controller Hub)
2.5, 2.6	Yes	in ACPI S0 state	ARCtangent-A4	ThreadX	T61p, T61, X300, X61, X61s, X61 Tablet
3.0, 3.1, 3.2	Yes	in ACPI S0 state	ARCtangent-A4	ThreadX	N/A (was featured only in the 82Q35 and 82Q43 Memory Controller Hub)
4.0, 4.1, 4.2	Yes	Yes	ARCtangent-A4	ThreadX	W700ds, W700, W500, T500, T400, T400s, X301, X200, X200s, X200 Tablet, R500, R400
5.0, 5.1, 5.2	Yes	in ACPI S0 state	ARCtangent-A4	ThreadX	N/A (was featured only in the 82Q45 Memory Controller Hub)
6.0, 6.1, 6.2	Yes	Yes	ARC 600	ThreadX	W701ds, W701, W510, T510, T510i, T410, T410i, T410s, T410si, X201, X201i, X201s, X201si, X201 Tablet, X201i Tablet
7.0, 7.1	Yes	Yes	ARC 600	ThreadX	W520, T520, T520i, T420, T420i, T420s, T420si, X220, X220i, X220 Tablet, X220i Tablet, X1, X1 Hybrid
8.0, 8.1	Yes	Yes	ARC 600	ThreadX	W530, T530, T530i, T430, T430i, T431s, T430s, T430si, T430u, X230, X230i, X230s, X230 Tablet, X230i Tablet, X1 Carbon, L530, L430
9.0, 9.1, 9.5	Yes	Yes	ARC 600	ThreadX	W541, W540, T540p, T440p, T440, T440s, T440, X240, X240s, X1 Carbon G2, L540, L440
10.0	Yes	Yes	ARC 600	ThreadX	W550s, T550, T450, T450s, X250, X1 Carbon G3, Template:L450
11.0, 11.5, 11.6, 11.7, 11.8, 11.11, 11.12, 11.22	Yes	Yes	unknown Quark	MINIX	Template:P70, Template:P50, Template:P50s, T560, T460, T460s, T460p, X260, X1 Carbon G4, Template:L560, Template:L460
12.0	Yes	Yes	unknown Quark	MINIX	Template:P71, Template:P51, Template:P51s, T570, T470, T470s, T470p, 25, X270, X1 Carbon G5, Template:L570, Template:L470
13.0	Yes	Yes	unknown Quark	MINIX	Template:P72, P52, Template:P52s, T580, T480, T480s, X280, X1 Carbon G6, Template:L580, Template:L480
14.0, 14.5	Yes	Yes	unknown Quark	MINIX	Template:P73, Template:P53, Template:P53s, T590, T490, T490s, X390, X1 Carbon G7, Template:L590, Template:L490

Features

Management over the Network (LAN and WLAN, using AMT 2.5)
Remote Asset (Hardware and Software) Inventory
Remote Diagnostic and repair (even if laptop is off or down)
Agent Presence Checking (isolate corrupted laptops)
Encrypted software update (w/ remote power-on).
System isolation and recovery (Use hardware to filter inbound and outbound traffic, except management traffic)
Dedicated Flash memory (Firmware + Inventory + ISV Data)

Linux support

The Linux heci driver to support iAMT was part of the staging tree as of the 2.6.30 kernel, but removed in 2.6.32 at the request of Intel as they have indicated having no further interest in it and have abandoned it.

Intel OpenAMT project website (abandoned)

Hints how to setup it via Intel ME BIOS Extension (MEBx) based on the T61p (Small business Mode)

Pre-configuration

Use ThinkVantage System Update so you have the latest BIOS
Reboot the system

Enabling AMT in BIOS

Hit the ThinkVantage button during the POST screen, then after the menu appears hit 'F1'
- Select 'Config' on the main screen
  - Select 'Intel(R) AMT'
    - Set 'Intel (R) AMT Control' to 'Enabled'
    - Hit 'F10' to Save and Exit

Configuring Intel ME BIOS Extension for the first time

After the POST screen you will see the Intel(R) Management Engine BIOS Extension screen.
Hit Ctrl+P to enter the setup.
Possibly press "1" to enter Intel(R) Management Engine BIOS Extension configuration screens.
On the first screen you can enter the Intel(R) ME Password.

The default password is 'admin' (without quotes)

If you try to change the Intel ME password and get "Error - Intel(R) ME password change rejected" message, then you are using a weak password.

Here are guidelines for the Intel(R) ME strong password:

- Comprise 8 to 32 characters
- including both upper and lower case characters
- including at least one numeric character
- including at least one ASCII non-alphanumeric character (!, @, #, $, %, ^, &, *)

Enabling AMT in Intel Management Engine BIOS Extension

On the main Management Engine Bios Extension page select Intel(R) ME Configuration
- Select 'Intel(R) ME State Control'
  - Set it ENABLED
  - Select Return to Previous Menu
- Select 'Intel(R) ME Firmware Local Update Qualifier'
  - Set it to ALWAYS OPEN
  - Select Return to Previous Menu
- Select 'Intel(R) ME Features Control'
  - Select 'Manageability Feature Selection'
    - Choose 'Intel(R) AMT'
  - Select Return to Previous menu
- Select 'Intel(R) ME Power Control'
  - Select 'Intel(R) ME ON in Host Sleep States'
    - Set the 'widest' range of Sleep States
    - Hit 'ESC' to Exit. The system will reboot now.

Configuring AMT via Intel ME

Hit Ctrl+P when the Intel ME BIOS messages apear
Select 'Intel(R) AMT Configuration'
- Select 'Host Name' and enter the same name as for the OS Host name
- Select 'TCP/IP'
  - Hit 'N' to enable the Network Interface
  - Hit 'N' to enable DHCP
  - provide your domain name as set (or to be set) in the OS
- Select 'Provision Model'
  - Hit 'N' to not change to AMT 1.0 Mode
  - Hit 'Y; to change to Small Business
- Select 'SOL/IDE-R'
  - Hit 'Y' to confirm the warning
  - Set Username & Password to ENABLED (if it's set to ENABLED don't hit just 'ENTER' because you disable it)
  - Set Serial Over LAN to ENABLED
  - Set IDE Redirection to ENABLED
- Select 'Secure Firmware Update'
  - Set it to ENABLED
- Hit 'ESC' to Exit. The system will reboot again.

Configuring Windows

Use ThinkVantage System Update to get the AMT Software
After update reboot
After Log-in you should see the message 'Intel(R) Active Management Technology (Intel(R) AMT) status on this computer is enabled.'

Firmware update

Lenovo provides Intel AMT firmware updates only in the form of Windows executables. Thus, if you don't have Windows installed on your laptop, for the purpose of updating Intel AMT firmware you will have to use Windows PE. Once you boot into Windows PE, before launching the firmware upgrade with (which you have to extract from Intel AMT Management Engine Firmware for Windows using ) you need to load HECI driver with "" (the HECI driver can be extracted with from Intel AMT Management Engine Interface for Windows).

URL: https://www.thinkwiki.org/wiki/Intel_Active_Management_Technology_(AMT)